Home  > INTERNATIONAL COMFORT PRODUCTS(x)  > (x)
|◀ ◀ 49 - 60 of 154 ▶ ▶|
View:

97% Modulating Communicating Gas Heating Furnace 35" H x 24-1/2" W x 29-1/2" D

  • Flame roll-out sensors standard
  • Adjustable heating blower OFF delay
  • Factory set blower ON delay
  • RPJ primary heat exchanger
  • Stainless steel secondary heat exchanger
  • High temperature limit control designed to prevent overheating
  • Direct ignition with Silicon Nitride ignitor
  • Operates quieter at lower heating rates
  • Variable speed induced draft combustion blower
  • Variable speed, constant airflow, communicating ECM blower motor
  • Insulated steel cabinet



    International Comfort Products G97CMN0602120B

    • Item#:
    G97CMN1202422B
    Manufacturer Item:
    G97CMN1202422B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G97CMN-Care_Misc
    G97CMN_Install
    G97CMN_Spec

    80% Variable Speed Gas Heating Furnace 33-1/3" H x 21" W x 29" D

  • 80% AFUE
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193
  • Supports twostage cooling units
  • ION Communicating Control System
  • Observer Communicating Control System
  • Flame rollout sensors standard
  • Category I venting
  • Blocked vent switch
  • Dehumidification feature in cooling
  • 24 VAC humidifier termina
    l
  • Electronic air cleaner terminal
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.



    International Comfort Products G80CTL1102120A

    • Item#:
    G80CTL1102120B
    Manufacturer Item:
    G80CTL1102120B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G80CTL-ICP-Care_Misc
    G80CTL-ICP_Install
    G80CTL-ICP_Spec

    80% Variable Speed Gas Heating Furnace 33-1/3" H x 21" W x 29" D

  • 80% AFUE
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193
  • Supports twostage cooling units
  • ION Communicating Control System
  • Observer Communicating Control System
  • Flame rollout sensors standard
  • Category I venting
  • Blocked vent switch
  • Dehumidification feature in cooling
  • 24 VAC humidifier termina
    l
  • Electronic air cleaner terminal
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.



    International Comfort Products G80CTL0902120B

    • Item#:
    G80CTL0902120B
    Manufacturer Item:
    G80CTL0902120B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G80CTL-ICP-Care_Misc
    G80CTL-ICP_Install
    G80CTL-ICP_Spec

    QuietComfort 96 Gas Heating Furnace 35" H x 17-1/2" W x 29-1/2" D

    FEATURES:
  • Up to 96% AFUE in upflow and horizontal positions 95% AFUE in downflow position
  • All models earn the ENERGY STAR®
  • Two-stage heating operation
  • Variable-speed, constant torque ECM blower motor for extra SEER boost with select cooling equipment
  • Supports single- and two-stage cooling units
  • Dehumidification feature in cooling
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193 TOUGHER
  • Flame roll-out sensors standard
  • Adjustable heating blower OFF delay
  • Factory set blower ON delay
  • RPJ primary heat exchanger
  • Stainless steel secondary heat exchanger
  • High temperature limit control prevents overheating
  • Direct ignition with Silicon Nitride ignitor QUIETER
  • Operates at quieter, lower heating rates
  • Two-speed induced draft combustion motor
  • Variable speed, constant torque ECM blower motor
  • Fully insulated steel cabinet EASIER TO INSTALL AND SERVICE
  • Direct vent (2-pipe), single-pipe venting or ventilated combustion air
  • 24 VAC humidifier terminal and electronic air cleaner terminal
  • 35 (889mm) high, for ease of installation
  • Quarter turn knobs for easy door removal and secure attachment conversion kits available
  • Four position upflow/downflow/horizontal (left/right) installation
  • At least twelve different venting configurations
  • Through the casing flue pipe for counterflow or horizontal applications with accessory (order separately)
  • Concentric vent available
  • Slide out heat exchanger assembly and blower assembly

    International Comfort Products G96VTN0601716B

    • Item#:
    G96VTN0801716B
    Manufacturer Item:
    G96VTN0801716B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G96VTN

    80% Variable Speed Gas Heating Furnace 33-1/3" H x 17-1/2" W x 29" D

  • 80% AFUE
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193
  • Supports twostage cooling units
  • ION Communicating Control System
  • Observer Communicating Control System
  • Flame rollout sensors standard
  • Category I venting
  • Blocked vent switch
  • Dehumidification feature in cooling
  • 24 VAC humidifier termina
    l
  • Electronic air cleaner terminal
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.



    International Comfort Products G80CTL0901716B

    • Item#:
    G80CTL0901716B
    Manufacturer Item:
    G80CTL0901716B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G80CTL-ICP-Care_Misc
    G80CTL-ICP_Install
    G80CTL-ICP_Spec

    80% Variable Speed Gas Heating Furnace 33-1/3" H x 17-1/2" W x 29" D

  • 80% AFUE
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193
  • Supports twostage cooling units
  • ION Communicating Control System
  • Observer Communicating Control System
  • Flame rollout sensors standard
  • Category I venting
  • Blocked vent switch
  • Dehumidification feature in cooling
  • 24 VAC humidifier termina
    l
  • Electronic air cleaner terminal
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.



    International Comfort Products G80CTL0701716B

    • Item#:
    G80CTL0701716B
    Manufacturer Item:
    G80CTL0701716B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G80CTL-ICP-Care_Misc
    G80CTL-ICP_Install
    G80CTL-ICP_Spec

    QuietComfort 96 Gas Heating Furnace 35" H x 21" W x 29-1/2" D

    FEATURES:
  • Up to 96% AFUE in upflow and horizontal positions 95% AFUE in downflow position
  • All models earn the ENERGY STAR®
  • Two-stage heating operation
  • Variable-speed, constant torque ECM blower motor for extra SEER boost with select cooling equipment
  • Supports single- and two-stage cooling units
  • Dehumidification feature in cooling
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193 TOUGHER
  • Flame roll-out sensors standard
  • Adjustable heating blower OFF delay
  • Factory set blower ON delay
  • RPJ primary heat exchanger
  • Stainless steel secondary heat exchanger
  • High temperature limit control prevents overheating
  • Direct ignition with Silicon Nitride ignitor QUIETER
  • Operates at quieter, lower heating rates
  • Two-speed induced draft combustion motor
  • Variable speed, constant torque ECM blower motor
  • Fully insulated steel cabinet EASIER TO INSTALL AND SERVICE
  • Direct vent (2-pipe), single-pipe venting or ventilated combustion air
  • 24 VAC humidifier terminal and electronic air cleaner terminal
  • 35 (889mm) high, for ease of installation
  • Quarter turn knobs for easy door removal and secure attachment conversion kits available
  • Four position upflow/downflow/horizontal (left/right) installation
  • At least twelve different venting configurations
  • Through the casing flue pipe for counterflow or horizontal applications with accessory (order separately)
  • Concentric vent available
  • Slide out heat exchanger assembly and blower assembly

    International Comfort Products G96VTN0801716B

    • Item#:
    G96VTN0802120B
    Manufacturer Item:
    G96VTN0802120B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G96VTN

    Ion 98 Variable-Speed Modulating Gas Heating Furnace 35" H x 21" W x 29-1/2" D

  • Flame roll-out sensors standard
  • Adjustable heating blower OFF delay
  • Factory set blower ON delay
  • RPJ primary heat exchanger
  • Stainless steel secondary heat exchanger
  • High temperature limit control designed to prevent overheating
  • Direct ignition with Silicon Nitride ignitor
  • Operates quieter at lower heating rates
  • Variable speed induced draft combustion blower
  • Variable speed, constant airflow, communicating ECM blower motor
  • Insulated steel cabinet



    International Comfort Products G97CMN0601714B

    • Item#:
    G97CMN1002122B
    Manufacturer Item:
    G97CMN1002122B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G97CMN-ICP-Care_Misc
    G97CMN-ICP_Install
    G97CMN-ICP_Spec

    80% Variable Speed Gas Heating Furnace 33-1/3" H x 21" W x 29" D

  • 80% AFUE
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193
  • Supports twostage cooling units
  • ION Communicating Control System
  • Observer Communicating Control System
  • Flame rollout sensors standard
  • Category I venting
  • Blocked vent switch
  • Dehumidification feature in cooling
  • 24 VAC humidifier termina
    l
  • Electronic air cleaner terminal
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.



    INTERNATIONAL COMFORT PRODUCTS G80CTL0702120A

    • Item#:
    G80CTL0702120A
    Manufacturer Item:
    G80CTL0702120A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G80CTL-ICP-Care_Misc
    G80CTL-ICP_Install
    G80CTL-ICP_Spec

    QuietComfort 96 Gas Heating Furnace 35" H x 21" W x 29-1/2" D

    FEATURES:
  • Up to 96% AFUE in upflow and horizontal positions 95% AFUE in downflow position
  • All models earn the ENERGY STAR®
  • Two-stage heating operation
  • Variable-speed, constant torque ECM blower motor for extra SEER boost with select cooling equipment
  • Supports single- and two-stage cooling units
  • Dehumidification feature in cooling
  • Low NOx units are designed for California installations and meet 40 ng/J NOx emissions. Can be installed in air quality management districts with a 40 ng/J NOx emissions requirement.
  • Cabinet air leakage less than 2.0% at 1.0 in. W.C. and cabinet air leakage less than 1.4% at 0.5 in. W.C. when tested in accordance with ASHRAE standard 193 TOUGHER
  • Flame roll-out sensors standard
  • Adjustable heating blower OFF delay
  • Factory set blower ON delay
  • RPJ primary heat exchanger
  • Stainless steel secondary heat exchanger
  • High temperature limit control prevents overheating
  • Direct ignition with Silicon Nitride ignitor QUIETER
  • Operates at quieter, lower heating rates
  • Two-speed induced draft combustion motor
  • Variable speed, constant torque ECM blower motor
  • Fully insulated steel cabinet EASIER TO INSTALL AND SERVICE
  • Direct vent (2-pipe), single-pipe venting or ventilated combustion air
  • 24 VAC humidifier terminal and electronic air cleaner terminal
  • 35 (889mm) high, for ease of installation
  • Quarter turn knobs for easy door removal and secure attachment conversion kits available
  • Four position upflow/downflow/horizontal (left/right) installation
  • At least twelve different venting configurations
  • Through the casing flue pipe for counterflow or horizontal applications with accessory (order separately)
  • Concentric vent available
  • Slide out heat exchanger assembly and blower assembly

    International Comfort Products G96VTN0802120B

    • Item#:
    G96VTN1002120B
    Manufacturer Item:
    G96VTN1002120B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G96VTN

    Ion 98 Variable-Speed Modulating Gas Heating Furnace 35" H x 17-1/2" W x 29-1/2" D

  • Flame roll-out sensors standard
  • Adjustable heating blower OFF delay
  • Factory set blower ON delay
  • RPJ primary heat exchanger
  • Stainless steel secondary heat exchanger
  • High temperature limit control designed to prevent overheating
  • Direct ignition with Silicon Nitride ignitor
  • Operates quieter at lower heating rates
  • Variable speed induced draft combustion blower
  • Variable speed, constant airflow, communicating ECM blower motor
  • Insulated steel cabinet



    International Comfort Products G96VTN1202422B

    • Item#:
    G97CMN0601714A
    Manufacturer Item:
    G97CMN0601714A
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G97CMN-ICP-Care_Misc
    G97CMN-ICP_Install
    G97CMN-ICP_Spec

    Ion 98 Variable-Speed Modulating Gas Heating Furnace 35" H x 17-1/2" W x 29-1/2" D

  • Flame roll-out sensors standard
  • Adjustable heating blower OFF delay
  • Factory set blower ON delay
  • RPJ primary heat exchanger
  • Stainless steel secondary heat exchanger
  • High temperature limit control designed to prevent overheating
  • Direct ignition with Silicon Nitride ignitor
  • Operates quieter at lower heating rates
  • Variable speed induced draft combustion blower
  • Variable speed, constant airflow, communicating ECM blower motor
  • Insulated steel cabinet



    International Comfort Products G97CMN0601714A

    • Item#:
    G97CMN0601714B
    Manufacturer Item:
    G97CMN0601714B
    Manufacturer:
    INTERNATIONAL COMFORT PRODUCTS
     
    G97CMN-ICP-Care_Misc
    G97CMN-ICP_Install
    G97CMN-ICP_Spec
    |◀ ◀ 49 - 60 of 154 ▶ ▶|
    View: