Henry Technologies S-9104H Brass Reservoir Pressure Valve, 3/8" SAE Female Flare x SAE Male Flare, 500 psi

• Proven design
• Two different pressure settings
• Premium quality teflon seal
• Stainless steel spring
• A reservoir pressure valve is used in a low pressure oil management system
• It is used to vent pressure in the oil reservoir while still maintaining a positive pressure differential between the Oil Reservoir and the compressor crankcase
• This positive pressure ensures an adequate oil supply to the oil level regulators
• The inlet of the valve should be connected directly to the oil reservoir and the outlet should be piped to suction pressure

,

S-9104H

,

S-9104H

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 1-1/8" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

,

D28-212

,

D28-212

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 1/2" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

D28-204

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 1-3/8" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

,

D28-313

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 1-5/8" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

,

D28-216

,

D28-216

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 2-1/8" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

,

F6315

,

F6315

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 3/8" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

D28-202

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 5/8" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

D28-206

Henry Technologies' Magni-Chek Valves are used in discharge lines to prevent flow from the condenser to the compressor during the"off" cycle, or to prevent flow from an operating Compressor to one that is idle. They are also used in liquid lines to prevent reverse flow through the unused expansion device on heat pump systems, or to prevent backup into the low pressure liquid line of a recirculating system during a defrost period. Henry Technologies Magni-Chek Valves are suitable for use with HFC and HCFC refrigerants and their associated oils, as well as other industrial fluids noncorrosive to copper, brass, steel and aluminum.

• Robust design
• Compact
• 7/8" OD
• Heat stabilized nylon seat ring for positive shut-off
• Positive back-seating with valve in open position
• Raised seat reduces debris induced sealing issues
• Large diameter diaphragm for greater lift, better flow and longer life
• Hermetic seal between bonnet, diaphragms and body

D28-210

Henry Technologies S-9130 Oil Level Regulator,

Henry Technologies S-9130

,

S-9130

The Henry Liquid Eye Sight has a unique"see-thru" feature that is more readable than other sight glasses. The dot on the tube is magnified when the tube is full of refrigerant to give a quick, easy indication.

• Shock resistant glass
• Color bar designed for HFC refrigerants
• Made in USA

SG1206

Henry Technologies S-5587 Non Serviceable Conventional Oil Separator, 7/8" ODS, 3/8" SAE Return, 1/8" NPT Drain

• The function of a helical oil separator is to remove oil from the discharge gas and return it to the compressor either directly or through an oil management system
• Conventional oil separators can be used in a wide variety of applications, common applications include multi-compressor racks and remote condensing units
• These separators are designed for use with scroll and reciprocating type compressors, they are not recommended for screw or rotary vane compressors
• Conventional oil separators are intended for low pressure oil management systems
• ODS refrigerant connection
• SAE flare oil connections
• Low pressure drop
• No moving parts within oil separation zone
• Magnet on oil float to collect debris
• The main components- shell, end caps and connections are made from carbon steel
• The separation screens are made from brass
• The float assemblies are made from stainless steel, brass and copper

,

S-5587

,

S-5587